Madawa Art Home Design

Archive for the ‘Tips’ Category

Safety is always of importance, especially when you have children and toddlers at home. Did you install the cable for the first time or do security checks on the existing home, follow these tips to ensure your electrical system in good condition.

Tips 1 – Socket power overload

overload sockets are common causes of household fires. Never put more plugs into the socket from which there is room for, and avoid using multi-socket adapter and the lead connections. Remember one plug in the socket.

Tip 2 – Socket Covers

Although the electrical outlet is too small for small fingers, they are not too small for a more imaginative items such as food, small toy parts, cutlery and other items. Take precaution of inserting the socket covers to stop all contacts in your house is empty.

Read the rest of this entry »

Incoming search terms:

A faulty switch is the inevitable consequence of wear. Although perhaps not so clear, the light is actually one of the most often we use in our everyday lives. Although the specific cause discomfort, a switch is damaged usually relatively easy to fix. Follow the tips below to get you switch and walk again.

1. The introduction of the Switch

Even if you do not have any technical skills, you can easily identify what type of switch you are dealing with. If the switch is broken in the bathroom or bedroom, this is probably a simple single pole switch. In this case, the switch usually has a “ON” and “OFF” printed on it and the switch only controls the lights in the rooms.

The rooms are larger, usually with the door two or more, tend to have a 3-way or 4-way switch. 3-way switch to control light from two points only, while the 4-way switch to control the operation of three or more points. This kind of switch does not have the usual “ON” and “OFF” printed, and 3-way is usually installed in pairs, so you may need to replace them.

Read the rest of this entry »

Incoming search terms:

A polarized plug will work with the best connection unless you connect it to a non-polarized outlet. In this case, you have a serious problem, because you can not connect the plug, because there will have extra holes that you need to power it, and you may not have a significant connection, such as earth wire. If you are looking for polarized connector for connecting to a socket, the conversion is the only answer, either by changing the plug, or by using an adapter that would allow a bridge between the two types of polarization. Both are very difficult, and you should be able to manage to complete this project in just a few minutes.

Materials Needed

* Screwdriver
* Conversion plug
* Adaptation Socket

Step 1 – Switch Install

You may find that you can get your polarized plug for the work that you remove the cable, and put in new plug with non-polarized outlet. This means that you find the extra wire polarized plug has been cut off during installation. You should find that the wire is there in the most modern equipment, as is considered a good idea to have three cables, including ground. Replace the plug as this is more dangerous, and you may find that you have to fit the new plate on the front of the socket.

Read the rest of this entry »

Incoming search terms:

A Generator Voltage Regulator is required to maintain a constant voltage in an AC or DC generator. While working, the generator engine to work at different speeds according to the output to be generated. Therefore over-worked machine can get hot and produce waves that can damage the generator. A voltage regulator that is widely used in cars to keep the battery from charging excessive and therefore not working.

Tools and Materials Needed:

* Voltage Regulator
* Batteries
* Generator AC / DC
* Fine sandpaper

Step 1: Pre-Installation

Check whether your generator is working before installing the regulator. Also check the battery condition as it is an integral part of the system. Wiring between the generator, regulator and batteries are often prone to corrosion that can be removed with fine sandpaper. Before you remove all cables from their relationship, tag them so you can reconnect them. Generators must be polarized before the exam regulator. Connect the positive terminal of the battery to the dynamo generator for the polarization. Remove batteries after this step. Although some countries have polarized the manual regulator is actually just means a generator because the regulator is not polarity sensitive.

Read the rest of this entry »

Incoming search terms:

Home generator transfer switch is a practical tool to have as back-up in the electricity goes out. This mechanism is the transfer of power from the generator to the home appliances when the power is not available. This is the materials you need along with instructions on how to install a home generator transfer switch.

Materials needed:

* Manual transfer switch
* Box inlet flange
* 240-amp circuit breaker
* Junction box
* Wire nuts
* ¾-inch Flexible channel
* Conduit connector

Read the rest of this entry »

Incoming search terms:

Fiberglass resin used to repair fiberglass surfaces, such as on motorcycles, cars, ships and aircraft. Because fiberglass can cause damage to one’s health, it is always important to use products with caution.

Here are some tips that can be very helpful during the application.

1. Wear Safety Equipment

When working with chemicals, always make sure you wear gloves and protective clothing to protect skin from direct contact. Fiberglass resin can be very itchy. It can also burn the skin so make sure you prepare a first aid kit in case.

Wear respirator as well. Resin must be mixed with a catalyst before it can be flexible. This chemical produces powerful steam and can cause damage to respiratory health. Wearing a respirator to ensure that smoke does not get directly inhaled.

Read the rest of this entry »

Incoming search terms: